-עקבו אחרינו ב

היבואן הרשמי של fluke בישראל

מבצעים
נפתחה הרשמה לקורס תרמוגרפיה /

יש לכם שאלה? צריכים הצעת מחיר?

פנו אל המומחים שלנו! השאר פרטיך ואנו נשוב אליך בהקדם

*שדה שם מלא הוא חובה *יש להזין מספר טלפון תקין

למידע נוסף והזמנות צור קשר


למידע נוסף מלאו פרטים
ונחזור אליכם בהקדם
* שדה שם מלא חובה * שדה הטלפון אינו תקין

Fluke 1770 SERIES

הסדרה החדשה Fluke 1770 מספקת פתרון בעיות במערכת החשמל, עם יכולות רישום מתח ואנרגיה עבור מגוון רחב של יישומים, בתוספת תוכנה נלווית להורדה, ניתוח ודיווח. פלטפורמה זו מאפשרת לטכנאי תחזוקה תעשייתיים, מנהלי תחזוקה ויועצים העוסקים בייצור, התקנת ציוד ושירות, לאתר מדידות עיקריות של איכות החשמל במהירות ובקלות.

סדרת 1770 מציעה מדידות אוטומטיות, ממשק משתמש והגדרה פשוטים, מפרטים מהטובים בתחום ופלטפורמת דיווח פשוטה. המכשיר יכול גם להיות מופעל ישירות ממעגל המדידה, מה שמבטל את הצורך למצוא שקע חשמל או להשתמש בכבל מאריך ארוך.

עם סדרת 1770 לעולם לא תפספס תופעת רשת קריטית – החל מקפיצות או הפרעות מתח עד 8 קילו וולט, הרמוניות עד 30 קילו-הרץ, נפילות, כמו גם מדידות מתח, זרם והספק המאפשרות לאפיין את אספקת האנרגיה למתקן.

לקבלת הצעת מחיר

Fluke 1770 SERIES

יתרונות המכשירים:
תצוגת מסך מגע עם כפתורי ניווט פיזיים וממשק משתמש מותאם.
• פונקציונליות הגדרה מודרכת כדי לאפשר הגדרה מהירה וחסינת תקלות בכל פעם, כולל היכולת לתקן אוטומטית חיבורי מדידה באופן דיגיטלי ללא צורך לשנות את חיבורי הבדיקה הפיזיים.
• העברת נתונים פשוטה ומהירה למחשב בעזרת -USB, Wi-Fiמואפשרות לחיבור מודם סללורי כל זאת מבלי להפריע למדידה.
• חבילת תוכנה מחודשת (Energy Analyze Plus) לניתוח ודיווח נתונים מודרניים ואינטואיטיביים
תכונות
Features
  • At-a-glance power quality health for faster troubleshooting
  • Automatically measure power and power quality parameters
  • Capture high-speed transients up to 8 kV
  • Easily view V/A/Hz
  • Power directly from measurement circuit without a line cord
מפרט

Voltage inputs
Number of inputs4 inputs, 3 phases and neutral referenced to PE (5 connectors)
Measurement category1000 V CAT III / 600 V CAT IV
Maximum input voltage1000 V rms / 1000 V dc (1700 Vpk)
Nominal voltage rangeWye and single phase: variable (50 V – 1000 V)
Delta: Variable (100 V – 1000 V)
IEC 61000-4-30 Class A compliance for the nominal voltages (Vdin) 100 V – 690 V
Input impedance10 MΩ between P-P and P-N, 5 MΩ between P-PE and N-PE
BandwidthDC to 30 kHz for PQ measurements, excluding transients
Resolution24-bit synchronous sampling
Sampling frequency80 kS/s at 50/60 Hz
Scaling1:1, variable for use of potential transformers
Voltage transients
Measurement range±8 kV
Sampling rate1775: 1 MS/s
1777: 1 MS/s, 20 MS/s
BandwidthDC to 1 MHz
TriggerAdjustable trigger level. Triggers on high-frequency components > 1.5 kHz
Resolution14-bit synchronous sampling
Current inputs
Number of inputs4 inputs 3 phases and Neutral, range selected automatically to attached sensor
RangeAC1 A to 1500 A with i17XX-FLEX1500 12
1 A to 1500 A with i17XX-FLEX1500 24
3 A to 3000 A with i17XX-FLEX3000 24
6 A to 6000 A with i17XX-FLEX6000 36
40 mA to 40 A with clamp i40s-EL
4 A to 400 A with clamp i400s-EL
DC20 A to 2000 A with 80i-2010-EL clamp
BandwidthDC to 30 kHz
Resolution24-bit synchronous sampling
Sampling frequency80 kS/s at 50/60 Hz
Scaling1:1, variable
Input voltageClamp: 50 mV / 500 mV rms; CF 2.8
Rogowski Coil: 15 mV / 150 mV rms at 50 Hz, 18 mV / 180 mV rms at 60 Hz; CF 4
all at nominal probe range
Input impedance11 kΩ
Data acquisition voltage and current
Input mains frequencyDC, 50/60 Hz 15 % (42.5 Hz … 57.5 Hz, 51 Hz … 69 Hz)
Topologies1-φ, 1-φ IT, Split phase, 3-φ delta, 3-φ wye IT, 3-φ Aron/Blondel (2 element delta), 3-φ delta open leg, 3-φ high leg delta
Data storageFluke 1773/1775: 8 GB internal (expandable with microSD card)
Fluke 1777: 32 GB microSD card (installed)
Memory sizeTypical 10 logging sessions of 8 weeks with 1-minute intervals and 100 events.
The number of possible logging sessions and logging period depends on user requirements
Real time accuracyInternal: 3 ppm (0.26 s per day, 8 s per month)
NTP (internet time): Depending on internet latency, typical < 0.1 s absolute to UTC
GPS: < 1 ms absolute to UTC
Aux inputs
Wired connection with 17XX-AUX adapter
Number of inputs2
Input rangeDirect: 0 V dc to ± 10 V dc
0 V to 1000 V dc
Input impedanceDirect: 2.92 MΩ
Scale factorFormat: mx + b (gain and offset) user configurable
Displayed unitsUser configurable (up to 8 characters, for example °C, psi, or m/s)
Data acquisition voltage and current
Input mains frequencyDC, 50/60 Hz 15 % (42.5 Hz … 57.5 Hz, 51 Hz … 69 Hz)
Topologies1-φ, 1-φ IT, Split phase, 3-φ delta, 3-φ wye IT, 3-φ Aron/Blondel (2 element delta), 3-φ delta open leg, 3-φ high leg delta
Data storageFluke 1773/1775: 8 GB internal (expandable with microSD card)
Fluke 1777: 32 GB microSD card (installed)
Memory sizeTypical 10 logging sessions of 8 weeks with 1-minute intervals and 100 events.
The number of possible logging sessions and logging period depends on user requirements
Real time accuracyInternal: 3 ppm (0.26 s per day, 8 s per month)
NTP (internet time): Depending on internet latency, typical < 0.1 s absolute to UTC
GPS: < 1 ms absolute to UTC
Trend interval
Measured parameterSee operator manual
Trend intervalUser selectable: 1 sec, 3 sec, 5 sec, 10 sec, 30 sec, 1 min, 5 min, 10 min, 15 min, 30 min
Averaging interval min/max valuesVoltage, Current: ½ cycle RMS (20 ms at 50 Hz, 16.7 ms at 60 Hz)
Aux, Power: 200 ms
Total harmonic distortionTHD for voltage and current is calculated on 50 harmonics
Power quality measurements
Measured parameterSee operator manual
Harmonicsh0 … h50
% fund and RMS for voltage, current and power
Phase angles for voltage and current up to h11
Interharmonicsih0… ih50
% fund and RMS for voltage and current
Supraharmonics2–9 kHz with 200 Hz bins
9–30 khz with 2 kHz bins
RMS for voltage and current
Harmonics measurement methodGrouped, sub-grouped and single harmonic bins according to IEC 61000-4-7.
Method selected automatically based on configured PQ standard or user configurable.
Total harmonic distortionCalculated on up to 50 harmonics (depends on selected PQ standard)
Mains signaling2 frequencies in the range from 110 Hz to 3000 Hz
EventsVoltageDip, swell, interruption, rapid voltage change, mains signaling, waveshape deviation, transients
CurrentInrush current
Triggered recordingsHalf cycle RMS of voltage and current for 10 s
Waveform of voltage and current for 10/12 cycles
Mains signaling: 200 ms RMS of mains signaling voltage up to 120 s
Transients: Waveform of voltage
(Fluke 1777: 1 MS/s or 20 MS/s, 500,000 pts, Fluke 1775: 1 MS/s, 25,000 pts)
Standard compliance
PowerIEEE 1459
HarmonicsIEC 61000-4-7: Class 1
IEEE 519 (short time and very short time harmonics)
FlickerIEC 61000-4-15 Class F1
Power qualityIEC 61000-4-30 Class A, IEC 62586 PQI-A-PI
Power quality complianceEN 50160 + GOST + NEQUAL + NETCODE + FOL
Interfaces
Ethernet1 Gbit/s 1000BASE-T
USB type AUSB 2.0 high speed for USB flash drives to transfer measurement data, firmware updates and license installation. Max. supply current: 500 mA
USB-CUSB 2.0 high speed for data download to PC and calibration (requires USB type A to USB-C or USB-C to USB-C cable)
Auxiliary power supply for the Analyzer (requires USB C power adapter PD 2.0 or higher with 9 V 1.8 A support)
USB 3.0 super-speed for USB-C flash drives to transfer measurement data, firmware updates and license installation. Max. supply current: 900 mA
WiFi/BLE module1802.11 ac 2.4 GHz / 5 GHz, support for concurrent access point and client mode
Bluetooth 5.0/BLE
Antenna: Internal and external2
LTE/4G module3LTE-A Cat 12
Worldwide LTE-A and UMTS/HSPA+ coverage
Antenna: External2
GPSMCX connector to attach a GNSS antenna for GPS/GLONASS2
1 Not in 177X/BASIC versions
2 Requires 5m extension cable, Fluke p/n 5263915
3 Availability and supported providers vary by country. Check with your local Fluke representative.

Electrical measurement accuracy

ParameterRangeResolutionIntrinsic Accuracy at Reference Conditions
% of Reading + % of Full Scale
Voltage1000 V0.1 V0.1 % of nominal voltage
in accordance with
IEC 61000-4-30 Class A1,2
±(0.04 % + 0.004 %)3
Voltage dips and swells0.1 V0.2 % of Vnom1,2
Voltage transients±8 kVpk±5 % +0.25 %)
Voltage harmonics/interharmonics100 %0.1 % / 0.1 mV≥1 % Vnom1: ±2.5 % of rdg.
<1 % Vnom1: ±0.025 Vnom
THD on voltage100 %0.1 % / 0.1 V±(2.5 % + 0.5 %)
Voltage distortions 2-9 kHzMax 100 V0.1 mV±(2.5 % + 0.1 V)
Voltage distortions 9-30 kHzMax 100 V0.1 mV±(2.5 % + 0.1 V)
Current
(Rogowski clamp mode)
With iFlex 1500 A,
i17XX-FLEX1500 24
150 A
1500 A
0.01 %
0.1 A
±(1 % + 0.02 %)
With iFlex 3000 A,
i17XX-FLEX3000 24
300 A
3000 A
0.01 A
0.1 A
±(1 % + 0.03 %)
With iFlex 6000 A,
i17XX-FLEX6000 36
600 A
6000 A
0.1 A
1 A
±(1.5 % + 0.03 %)
With AC clamp 40 A,
i40s-EL
4 A
40 A
0.001 A
0.01 A
±(0.7 % + 0.02 %)
With AC clamp 400 A,
i400s-EL
40 A
400 A
0.01 A
0.1 A
±(2 % + 0.2 %)
±(0.7 % + 0.1 %)
With AC/DC clamp
2000 A, 80i-2010s-EL
200 A
2000 A
0.01 A
0.1 A
±(0.8 % + 0.2 %)
Current min/max100 %defined by accessoryx2 of intrinsic accuracy
Current harmonics/interharmonics100 %0.1 % / 0.01 A≥3 % Inom: ±2.5 % of rdg.4
<3 % Inom: ±0.15 % of Inom
THD on current100 %0.1 %±(2.5 % + 0.5 %)
Frequency42.5 Hz … 69 Hz0.001 Hz±0.01 Hz
Voltage unbalance100 %0.1 %±0.15 %
Current unbalance100 %0.1 %±0.15 %
Flicker Pinst, Pst, Plt0 to 200.015 %
Mains signaling voltageUp to 3 kHz
0-15 % of Vnom
0.1 V / 0.1 %1-3 % Vnom: ±0.15 % of Vnom
3-15 % Vnom: ±5 % of rdg.
AUX input±10 V0.1 mV±(0.2 % + 0.05 %)
1 Nominal voltage in the range of 100 V to 690 V. Also known as Udin.
2 0 °C to 45 °C: Intrinsic Accuracy x2. Outside of 0 °C to 45 °C: Intrinsic Accuracy x3
3 Only for calibration laboratories
4 With iFlex 1500A, I17XX-FLEX1500 24

Power/Energy

ParameterDirect Input1Clamp i40S-EL
Power range W, VA, varClamp: 50 mV / 500 mV
Rogowski: 15 mV / 150 mV
4 A / 40 A
Clamp: 50 W / 500 W
Rogowski: 15 W / 150 W
4k W / 40 kW
Max. resolution W, VA, var0.1 W1 W / 10 W
Phase (voltage to current)1±0.2°±1°
ParameteriFlex 1500A, I17XX-FLEX1500 24iFlex 3000A, I17XX-FLEX3000iFlex 6000A, I17XX-FLEX6000
Power range W, VA, var150 A / 1500 A300 A / 3000 A600 A / 6000 A
150 kW / 1.5 MW300 kW / 3 MW600 kW / 6 MW
Max. resolution W, VA, var0.1 kW / 1kW1 kW /10 kW1 kW / 10k W
ParameterI17XX-FLEX1500 24I17XX-FLEX3000I17XX-FLEX6000
Active power PPF ≥ 0.99150 A / 1500 A300 A / 3000 A600/6000 A
1.2 % + 0.005 %1.2 % + 0.0075 %1.7 % + 0.0075 %
Active energy Ea0.1 ≤ PF < 0.99(1.2+√(1-PF2)/(2 PF)) % + 0.005 %(1.2+√(1-PF2)/(2 PF)) % + 0.0075 %(1.7+√(1-PF2)/(2 PF)) % + 0.0075 %
Apparent power S
Apparent energy Eap
0 ≤ PF ≤ 11.2 % + 0.005 %1.2 % + 0.0075 %1.7 % + 0.0075 %
Reactive power Q
Reactive energy Er
0 ≤ PF ≤ 12.5 % of measured apparent power/energy
Additional uncertainty
(% of power high range)
VP-N > 250 V0.02 %0.02 %0.02 %
Phase (voltage to current)0.28°0.28°0.28°

1 Nominal voltage in the range of 100 V to 690 V. Also known as Udin.

Reference Conditions

Environmental: 23 °C ±5 °C, instrument operating for at least 30 minutes, no external electrical/magnetic field, RH <65 %

Input conditions: Cos Φ/PF=1, Sinusoidal signal f=50/60 Hz, power supply 120 V/230 V ±10 %.

Current and power specifications: Input voltage >100V

Input current > 10 % of current range

Primary conductor of clamps or Rogowski coil in center position

Temperature coefficient: Add 0.1 x specified accuracy for each degree °C above 28 °C or below 18 °C

General specifications

Key features
WarrantyAnalyzer: 2 years (battery not included)
Accessories: 1 year (including battery)
Calibration cycle2 years
Size (L X W X HD)28.0 cm x 19.0 cm x 6.2 cm (11.0 in x 7.5 in x 2.4 in)
Weight2.1 kg (4.6 lb)
Anti-theft protectionSlot to support Kensington lock
Environmental specifications
Operating temperature range-10 °C to 50 °C
Storage temperature range-20 °C to 60 °C
Operating humidityIEC 60721-3-3: 3K5, modified:
-10 °C to 30 °C: ≤95 %, no condensation or ice
35 °C: 70 %
40 °C: 55 %
50 °C: 35 %
IP RatingIEC 60529: IP50
VibrationIEC 60721-3-3 / 3M2
Power supply
Voltage range100 V – 600 V -15 % / +10 % (85 V … 660 V)
Power consumptionMax. 40 VA
Mains frequency50/60 Hz (42.5 Hz … 69 Hz)
UPSLi-Ion battery BP1770 with extended temperature range, customer replaceable
On-battery runtime: 1.5 hours
Safety
GeneralIEC 61010-1: Pollution Degree 2
Power supplyOvervoltage Category IV 600 V
With Mains Adapter MA-C8: Overvoltage Category II 300 V
MeasurementIEC 61010-2-030: CAT IV 600 V, CAT III 1000 V
Altitudes 2000 m to 4000 mDerate to:
Power Supply: Category IV 300 V
With MA-C8 Adapter: Category II 150 V
Measurement: CAT IV 300 V, CAT III 600 V, CAT II 1000 V
מסמכים